« previous next »
Pages: [1] 2 3   Go Down

Author Topic: new updated 562xp  (Read 3220 times)

0 Members and 52 Guests are viewing this topic.

Offline

  • 4 cube
  • **
  • Posts: 54
  • Karma: 2

    • Total Badges: 14
    Badges: (View All)
    One year Anniversary 50 Posts 10 Posts Level 3 Karma Topic Starter
new updated 562xp
« on: March 08, 2013, 05:18:24 am »
can anyone tell me what causes this saw to run like this after i cut a while with it does not do it at all cold this is my second one of these saws this is the updated one sn:2012 2700690 saw has about 4 tanks through it heres the link
Logged

Share on Bluesky Share on Facebook

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

    • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: new updated 562xp
« Reply #1 on: March 08, 2013, 05:31:05 am »
Sounds like it is lean at idle?
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline

  • 6 cube
  • ****
  • Posts: 237
  • Karma: 26
  • Location: Sweden
    • Chainsaw Collectors Forum

    • Total Badges: 23
    Badges: (View All)
    Linux User Third year Anniversary Level 5 Signature Avatar Mobile User
Re: new updated 562xp
« Reply #2 on: March 08, 2013, 06:22:59 am »
You just cut cookies? No limbing?
Run it as you normally would it will "learn".
If you do the cuts, the limbing and run it normally it will figure it out and adapt.

Was it "reset" after update? It has to be told there was a change. If not it will not know, think it is the same and try to adapt accordingly.

If it still do it after two tanks get it hooked up and see if all is correct.
Logged
Chainsaw nut!

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24888
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: new updated 562xp
« Reply #3 on: March 08, 2013, 01:14:06 pm »
Are you talking about a hesitation off idle when you wot it?
Logged

Offline

  • 4 cube
  • **
  • Posts: 54
  • Karma: 2

    • Total Badges: 14
    Badges: (View All)
    One year Anniversary 50 Posts 10 Posts Level 3 Karma Topic Starter
Re: new updated 562xp
« Reply #4 on: March 08, 2013, 01:33:01 pm »
Quote from: Magnus on March 08, 2013, 06:22:59 am
You just cut cookies? No limbing?
Run it as you normally would it will "learn".
If you do the cuts, the limbing and run it normally it will figure it out and adapt.

Was it "reset" after update? It has to be told there was a change. If not it will not know, think it is the same and try to adapt accordingly.

If it still do it after two tanks get it hooked up and see if all is correct.
yes the dealer reset it and did a 3-5 min cut with it
Logged

Offline

  • 4 cube
  • **
  • Posts: 54
  • Karma: 2

    • Total Badges: 14
    Badges: (View All)
    One year Anniversary 50 Posts 10 Posts Level 3 Karma Topic Starter
Re: new updated 562xp
« Reply #5 on: March 08, 2013, 01:41:20 pm »
Quote from: Cut4fun_ on March 08, 2013, 01:14:06 pm
Are you talking about a hesitation off idle when you wot it?
yes i had the older one that did it i took it back and got a new one this one has the new coil,carb and computer ,my dealer said there is no known fix for it some do it and some don't
Logged

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24888
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: new updated 562xp
« Reply #6 on: March 08, 2013, 01:47:17 pm »
mweba has found a adjustment on the carb for that.
Logged

Offline

  • 4 cube
  • **
  • Posts: 54
  • Karma: 2

    • Total Badges: 14
    Badges: (View All)
    One year Anniversary 50 Posts 10 Posts Level 3 Karma Topic Starter
Re: new updated 562xp
« Reply #7 on: March 08, 2013, 02:03:44 pm »
Quote from: Cut4fun_ on March 08, 2013, 01:47:17 pm
mweba has found a adjustment on the carb for that.
yeah i was talking to him he told me a couple things it could be just haven't tried it yet  going to do that today
Logged

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24888
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: new updated 562xp
« Reply #8 on: March 08, 2013, 02:05:31 pm »
I didnt want to post his pics without him doing it.  I also ask him about sharing pic if he would.

 Seems real easy and straight forward adjustment.  ;)
Logged

Offline

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55

    • Total Badges: 32
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: new updated 562xp
« Reply #9 on: March 08, 2013, 02:17:08 pm »
The 562 carb does not have an air vain adjustment like the 550.....yet.    I have some new 562's coming, does anyone know if they switched to Walbro on the latest update?


If I was to have the saw in my possession, an adjustment could be made but would not recommend it to someone without a diag tool.

Which carb does your saw have, Don?
Logged
Pages: [1] 2 3   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
6 Replies
4268 Views 		Last post February 20, 2024, 07:34:25 am
by Cut4fun .
25 Replies
5254 Views 		Last post June 25, 2014, 04:48:31 pm
by KilliansRedLeo
230 Replies
26129 Views 		Last post February 18, 2023, 08:34:43 am
by Cut4fun
18 Replies
5589 Views 		Last post November 24, 2015, 10:24:58 am
by SawTroll
28 Replies
3131 Views 		Last post July 19, 2017, 07:45:14 am
by Nixon
8 Replies
2777 Views 		Last post November 13, 2018, 11:41:46 am
by Cut4fun .
5 Replies
1520 Views 		Last post February 24, 2019, 06:34:46 pm
by Cut4fun .
7 Replies
4300 Views 		Last post November 19, 2020, 08:40:48 pm
by Derf
6 Replies
2713 Views 		Last post January 11, 2022, 03:12:02 pm
by Tys78
0 Replies
91 Views 		Last post December 13, 2025, 09:12:22 am
by Cut4fun .