Author Topic: caveman STA .... Help, Questions, Problems, Bugs and general WTF? (Read 3244 times)

1manband · « **on:** November 27, 2013, 04:37:56 pm »

starting this thread to hopefully keep replies in one place. will do what i can to help folks get through it.

if a person has a problem(s) with it, most likely, someone else has the same problem.

not going to answer questions on other forums about it. like the free idea and want it to stay here, for members to use with sucess, or maybe to curse at. like the folks and information shared here. other site has watered down of late.

the spreadsheet will be password protected for the first couple of months. not because its secret or anything, just want forum members to have the first crack at it. if someone wants a password for it, during this time, pm me. not a member, you will have to wait, or join and share something you know.

will post the spreadsheet later this evening. have to hook the old pc up with a cord to the internet up from the basement, am taking a break for now, eyes are buggy from looking at screen for hours.

one last thing. the program does not and should not contain any macros. if a version out there contains these things, do not download it. my pc does not have any virus's, but run a virus scan on the program before you open it. if any of you have a filechecker, i will post the md5 and file size. if the file size is larger than what i have listed to be true, do not download it. pm me if unsure.

may need a varience on the file size.

regards
-joe

Cut4fun . · « **Reply #1 on:** November 27, 2013, 04:47:22 pm »

Thank you for your time and sharing this with the members. We are all about doing things for FREE here.

I have access to a 1996 chainsaw workshop time line online. It's also password protected.

If you do have your own business or shop etc fill free to post in your sig or where to buy online here too.

Kevin

1manband · « **Reply #2 on:** November 27, 2013, 10:53:07 pm »

tomorrow. sound like a broken record. ate dinner, then a 12oz beverage hit the stomach.

macros. i don't actually know for sure if it will have a macro or not on your end. as i mentioned, for the time being it will have a password. then i have a program that codes the calculations to remain hidden from view. maybe someone more computer savvy than i will know if it contains a macro or not by doing these things. asked randy about zipping the file, because it is too large. am trying to find info on that. maybe you guys will need that program as well. don't know much about it.

-joe

660magnum · « **Reply #3 on:** November 27, 2013, 11:19:58 pm »

You can use "Google Drive" as a intermediary download repository? It will come up automatically with a large file if you use "Gmail".

Cut4fun . · « **Reply #4 on:** November 28, 2013, 12:13:11 pm »

I can fix the to large file uploading prob on my end. What size is it in kb or mb?
Send link or whatever to my email I sent you. Might take me a a day or 2 to embed.

1manband · « **Reply #5 on:** December 01, 2013, 06:29:16 am »

thanks, will do cut4fun, if it ends up being too large. its too large to attach without shrinking it down as it is. the zip thing may end up shrinking it enough to post directly.

from what i gathered, folks will need to unzip the file. maybe some newer computers will have something installed on them to do this. will try to zip it using zzip. its a free, general public license software. winzip and winrar can also do it, but think that they are "shareware" (free at first, then pay to play or something like that). dont know enough about "how" to unzip yet, to write some instructions. hopefully, its easy enough to do for everyone.

delay is over. got everything solved and working as it should.

1manband · « **Reply #6 on:** December 01, 2013, 11:35:34 am »

its now up on the other thread.

if there is issues with the "unzpping" thing..... mabye someone could post on how to do that.

thanks
-omb

1manband · « **Reply #7 on:** December 02, 2013, 05:34:13 am »

folks trying this out:

need to know what you have before getting what you want.

works like this in a nutshell.
1. known baseline power levels are entered
2. baseline motor is blueprinted using measurements:
only difference from the way most of yall seem to do this is that port widths need to be measured as well;
also differs that the degree measurements need to be converted into millimeters. to get the areas.
3. then your baseline motor sta's are calculated.
4. you then save this info
5. you then re-run the spreadsheet, with the target motor gain level you choose.
6. it calculates a new target sta needed to get that power
7. now, knowing the new sta now needed, you just change heights and/or widths to match those needed to get the target sta.
8. target motor now blueprinted.

-omb

pops21 · « **Reply #8 on:** December 02, 2013, 01:29:00 pm »

Holy batman. I'm going to give it a shot. Its going to take ALOT of reading and rereading to get some numbers flowing.

pops21 · « **Reply #9 on:** December 03, 2013, 10:14:54 am »

Ok I started plugging in some numbers on the BMEP choices and input values to get the ball rolling. If all goes well you say to rerun the spread sheat after all the numbers for the every sheet to get target numbers. What do you mean by that. I guess what I'm saying is after I get all the numbers plugged in where are the numbers I need to use to get the desired results? Maybe I'm not seeing it. Also what are the intake port 1 and intake port 2 for? Same goes for exhaust and transfer ports too. It might take me a while but I and determined to put this program from step one to final result. One thing that I think might help is a spread sheet that is maybe already done as a example. I'm sure I will have more questions.

Subject / Started by	Replies	Last post
husqvarna running problems Started by nipstar Husqvarna	5 Replies 2816 Views	January 02, 2013, 08:23:58 am by William Greene
2100 problems Started by darren_palms Husqvarna	5 Replies 1827 Views	January 27, 2013, 11:42:57 am by Al Smith
Ignition Problems? Started by riverrocket Stihl	4 Replies 1637 Views	March 22, 2013, 10:13:50 pm by 660magnum
husqvarna 141 running problems Started by banditman Husqvarna	6 Replies 4543 Views	June 02, 2013, 09:30:02 pm by brokenbudget
Stihl Chainsaw AV Design and Possible Boot Problems Started by 660magnum « 1 2 » Stihl	12 Replies 2270 Views	October 19, 2013, 03:30:14 pm by jmester
specific time/area "caveman" spreadsheet Started by 1manband « 1 2 ... 5 6 » How To Basics and Fixes	57 Replies 11842 Views	January 01, 2014, 07:56:48 pm by Cut4fun .
stihl 066 old girl ignition problems Started by spearpainting Stihl	8 Replies 2576 Views	October 04, 2014, 09:16:30 am by aclarke
Jonsered 80/801/90 ignition system problems Started by awol Jonsered	7 Replies 2665 Views	December 15, 2014, 05:05:15 pm by 660magnum
PP 335 - General Service Questions Started by Hoggwood « 1 2 ... 5 6 » Poulan	50 Replies 2615 Views	February 02, 2015, 10:03:16 am by Cut4fun .
General Case assembly tool Started by weimedog Tool Shed	0 Replies 1369 Views	March 29, 2017, 10:19:50 am by weimedog

Chainsaw Repair

News:

Author Topic: caveman STA .... Help, Questions, Problems, Bugs and general WTF? (Read 3244 times)

1manband

caveman STA .... Help, Questions, Problems, Bugs and general WTF?

Cut4fun .

Re: caveman STA .... Help, Questions, Problems, Bugs and general WTF?

1manband

Re: caveman STA .... Help, Questions, Problems, Bugs and general WTF?

660magnum

Re: caveman STA .... Help, Questions, Problems, Bugs and general WTF?

Cut4fun .

Re: caveman STA .... Help, Questions, Problems, Bugs and general WTF?

1manband

Re: caveman STA .... Help, Questions, Problems, Bugs and general WTF?

1manband

Re: caveman STA .... Help, Questions, Problems, Bugs and general WTF?

1manband

Re: caveman STA .... Help, Questions, Problems, Bugs and general WTF?

pops21

Re: caveman STA .... Help, Questions, Problems, Bugs and general WTF?

pops21

Re: caveman STA .... Help, Questions, Problems, Bugs and general WTF?

Related Topics