« previous next »
Pages: [1]   Go Down

Author Topic: ms660  (Read 1256 times)

0 Members and 63 Guests are viewing this topic.

Offline

  • 4 cube
  • **
  • Posts: 54
  • Karma: 2

    • Total Badges: 14
    Badges: (View All)
    One year Anniversary 50 Posts 10 Posts Level 3 Karma Topic Starter
ms660
« on: December 27, 2013, 05:41:13 pm »
can anyone tell me what would be blowing my pull starter pawls,clip and real apart, the real  pawls clip are aftermarket are they just that much junk or could it be something with the fan shroud it's self,the saw is a 064 crank case with a 660 crank,polymer flywheel and top end
Logged

Share on Bluesky Share on Facebook

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1968
  • Karma: 171

    • Total Badges: 31
    Badges: (View All)
    Level 6 Sixth year Anniversary Fifth year Anniversary 1000 Posts Fourth year Anniversary 500 Posts
Re: ms660
« Reply #1 on: December 27, 2013, 05:50:34 pm »
It may be aftermarket junk or there's something in a bind. Check to make sure it's not rubbing on something in there. 
Logged

Offline

  • 4 cube
  • **
  • Posts: 54
  • Karma: 2

    • Total Badges: 14
    Badges: (View All)
    One year Anniversary 50 Posts 10 Posts Level 3 Karma Topic Starter
Re: ms660
« Reply #2 on: December 27, 2013, 06:12:16 pm »
this is the 3rd set of aftermarket it blow apart
Logged

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2114
  • Karma: 172
  • Location: VA

    • Total Badges: 36
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Level 6
Re: ms660
« Reply #3 on: December 27, 2013, 08:03:43 pm »
Try putting some grease on the rotor axle (sprocket tip grease)  I would have to say that if it is your third am set that has went bad, I would be trying an oe set. But like gatekeeper said check for some thing binding up on you. Also make sure the spring clip is not bent or deformed. If it falls off there is nothing else to hold it together.
Logged

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24888
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: ms660
« Reply #4 on: December 27, 2013, 10:07:06 pm »
I had a prob with 066 recoil once.  When you install everything before putting on saw. Are you testing. Pull rope quick with recoil off and see if pawls pop out and then go back in smoothly and quickly when you let rope retract.
Logged

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2114
  • Karma: 172
  • Location: VA

    • Total Badges: 36
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Level 6
Re: ms660
« Reply #5 on: December 27, 2013, 11:56:11 pm »
Agreed with cut make sure the pawls expand and contract like they should. Had the same thing happen on a 460 once trashed everything, rotor,pawls,washer,spring clip,and pull cord all down the drain.
Logged

Offline

  • 4 cube
  • **
  • Posts: 54
  • Karma: 2

    • Total Badges: 14
    Badges: (View All)
    One year Anniversary 50 Posts 10 Posts Level 3 Karma Topic Starter
Re: ms660
« Reply #6 on: December 28, 2013, 12:18:44 am »
i did check that they were coming out but didn't notice if they was going in all the way when i get the new oem parts this time, ill check that out.thanks guys
Logged

Offline

  • Piped Saw
  • *****
  • Posts: 309
  • Karma: 39

    • Total Badges: 19
    Badges: (View All)
    Second year Anniversary One year Anniversary Search Level 4 100 Posts 50 Posts
Re: ms660
« Reply #7 on: December 30, 2013, 12:51:57 pm »
I have never had much luck with aftermarket starter parts for any brand.
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
9 Replies
6661 Views 		Last post February 25, 2012, 08:34:02 am
by 2spud
2 Replies
1473 Views 		Last post March 13, 2012, 08:20:33 pm
by 660magnum
4 Replies
1704 Views 		Last post August 31, 2013, 03:22:53 pm
by Fish
1 Replies
1496 Views 		Last post February 05, 2014, 08:38:42 pm
by Cut4fun .
7 Replies
1963 Views 		Last post September 12, 2014, 07:50:51 pm
by 660magnum
0 Replies
1030 Views 		Last post February 04, 2015, 10:27:58 am
by farmboy
1 Replies
2554 Views 		Last post March 02, 2016, 10:15:56 pm
by Ozarker
0 Replies
797 Views 		Last post May 21, 2016, 09:52:45 am
by weimedog
0 Replies
1805 Views 		Last post November 26, 2016, 02:32:54 pm
by weimedog
3 Replies
961 Views 		Last post December 12, 2017, 09:40:25 pm
by sawyer tom