« previous next »
Pages: 1 ... 32 33 34 35 36 [37]   Go Down

Author Topic: Poulan 475  (Read 123164 times)

0 Members and 1 Guest are viewing this topic.

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4941
  • Karma: 216
  • OHIO REDNECK

    • Total Badges: 44
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Level 7 Seventh year Anniversary Apple User
Re: Poulan 475
« Reply #360 on: April 28, 2025, 01:25:48 pm »
Quote from: Cut4fun . on April 22, 2024, 12:02:30 pm
@3000 FPS    I checked that old meteor piston today. One you bought for 475 but could tell way off.

Checked. Is a 046 460 piston spec with the wider pin boss for husky poulan jred crank small end. For 475 2077 by meteor.
But as you see not right. 5

52mm 064 piston works better by opening pin bosses as is the 066 660 piston is too for 54mm.

Meteor's failed attempt at poulan 475 jonsered 2077 2083II piston.



Roger finally a use for that piston.  @3000 FPS

It wouldnt have fit the crank rod in the 475 without opening.

I just remembered I had a 52mm meteor piston.  That was a failed attempt by them to make the poulan 475 jonsered 2077 2083II.

Wasn’t even close looked like 460 piston by specs.

Looks like I got piston already. 😎 For G466

The meteor fits the rod better the the FT one.

Pin wide 15.57mm to 15.93mm roughly.

Piston weights bare





Logged
Like Like x 1 View List

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24887
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulan 475
« Reply #361 on: April 29, 2025, 03:12:35 pm »
I test fit that poulan meteor piston on a poulan 475 crank and it would go on.

So the Farmertec G466 stihl pistons just wider even yet already between pin bosses. 

Stihl oem need widen up to use if 064 piston used.
Logged

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24887
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulan 475
« Reply #362 on: August 20, 2025, 09:24:09 am »
I ended up buying all 6 of those OEM poulan 475 415 pto side crank seals last year or during winter.   

Anyhow only 3 of the 6 left now.



Logged
Pages: 1 ... 32 33 34 35 36 [37]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
Poulan 365

Started by Cut4fun « 1 2 ... 17 18 » Poulan

172 Replies
19843 Views 		Last post April 29, 2024, 07:46:12 am
by Cut4fun .
Poulan 295 Porting

Started by Dh1984 « 1 2 » Poulan

11 Replies
8083 Views 		Last post May 20, 2011, 08:55:11 am
by Dh1984
3 Replies
2229 Views 		Last post June 11, 2011, 05:25:29 pm
by Cut4fun
Poulan pro 236

Started by Cut4fun . « 1 2 ... 5 6 » Poulan

52 Replies
10345 Views 		Last post November 03, 2020, 07:28:29 am
by Cut4fun .
230 Replies
33191 Views 		Last post May 31, 2026, 07:09:38 am
by Cut4fun
4 Replies
5440 Views 		Last post November 23, 2012, 12:28:15 am
by Andyshine77
23 Replies
19563 Views 		Last post November 02, 2015, 04:36:50 pm
by Cut4fun .
7 Replies
9800 Views 		Last post September 10, 2023, 10:51:03 am
by Cut4fun .
2 Replies
3547 Views 		Last post May 21, 2017, 08:59:45 pm
by Cut4fun .
1 Replies
2239 Views 		Last post May 29, 2021, 08:42:15 pm
by 3000 FPS