« previous next »
Pages: [1]   Go Down

Author Topic: Another 028 post  (Read 1324 times)

0 Members and 61 Guests are viewing this topic.

Offline

  • 6 cube
  • ****
  • Posts: 179
  • Karma: 7

    • Total Badges: 19
    Badges: (View All)
    Apple User Third year Anniversary Second year Anniversary Level 4 One year Anniversary Linux User
Another 028 post
« on: December 23, 2016, 06:05:55 pm »
Without any disassembly, is there any way to know for sure that I'm looking at a Super rather than a WB, AV, AVEQ, etc.?

Thank you
Logged
Sthil Man. 011AV, 015, 020, 020, 024, 025, 026, 028 WB(2), 028AV, 028 Super, 029 Super(2), 039, 041, 192TC, 200T, 250, 260, 390, 440, 441

Share on Bluesky Share on Facebook

Offline

  • 3 cube
  • *
  • Posts: 7
  • Karma: 4

    • Total Badges: 13
    Badges: (View All)
    One year Anniversary Search Level 3 Poll Voter Karma Combination
Re: Another 028 post
« Reply #1 on: December 24, 2016, 11:04:09 am »
I believe the supers had a factory pop up piston. I could be wrong. pop the muffler and peek in there.
Logged

Offline

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC

    • Total Badges: 31
    Badges: (View All)
    Level 6 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary 1000 Posts Old Browser
Re: Another 028 post
« Reply #2 on: December 24, 2016, 08:34:00 pm »
Super 46mm does have a popup been used in 55 Husky 46mm.
Shep
Logged

Offline

  • 4 cube
  • **
  • Posts: 45
  • Karma: 6
  • Location: UK

    • Total Badges: 19
    Badges: (View All)
    Avatar Fifth year Anniversary Fourth year Anniversary Level 4 Level 3 10 Posts
Re: Another 028 post
« Reply #3 on: December 30, 2016, 04:16:11 pm »
I had to do this recently. Only way I could be sure was to remove the exhaust and using one of those wood coffee stirrer sticks (which are ideally rounded on the ends for this kind of job) I inserted it across the top of the piston and butted it up against the far cylinder wall, then gently lifted the piston via the recoil until it indented the wooden stirrer. Then remove it and measure the piston diameter.
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
1 Replies
1165 Views 		Last post May 26, 2011, 09:25:06 pm
by rgclmc
16 Replies
4044 Views 		Last post November 22, 2011, 09:24:11 am
by Al Smith
16 Replies
5077 Views 		Last post May 21, 2012, 05:10:04 pm
by man of stihl
19 Replies
5220 Views 		Last post November 25, 2015, 07:02:55 am
by 660magnum
1 Replies
1320 Views 		Last post July 25, 2015, 12:21:40 pm
by Cut4fun .
15 Replies
2084 Views 		Last post April 05, 2016, 03:10:56 pm
by 3000 FPS